Installation of a gas boiler standards, requirements, rules

From the author: Greetings, dear friends! We suggest we talk about how to install a gas convector with your own hands . These heating devices are less popular among consumers than their electric counterparts. The fact is that this type of heater implies the presence of a centralized gas supply or a gas cylinder. But such models are much cheaper to operate. They are usually installed in dachas or country cottages - that is, in those locations that do not require constant heating.

Sandwich chimney device

For a wooden building, this system is an ideal option.
Such a chimney consists of two pipes of different diameters located one inside the other. A heat insulator is placed between their walls. Such a chimney installed in a wooden house differs from a traditional brick one in a lot of advantages. Watch the video about the sandwich pipe:

The roof structure, made of wooden materials, even when dried well, seems to play a little over time. Displacements invisible to the eye and seemingly insignificant can lead to the destruction of a brick chimney, even the hardest one. But the sandwich, thanks to its design features, is not afraid of these threats.

And it is not surprising that the chimney in a wooden private house is increasingly being made in exactly this way. All its many advantages include the excellent fire safety of the pipe compared to a brick pipe.

Installation of gas stove and convectors

It is prohibited to install the convector at a distance of less than 4 meters from open sources of fire, including a gas stove. The hose suitable for the convector must have a dielectric insert, this will prevent a fire in the event of a short circuit in the wiring in a wooden house.

An important factor is the grounding of sockets located near the gas stove and convectors, although in a wooden house they should be grounded a priori.

There are three types of supply hoses that are allowed for a gas stove in a wooden house, namely:

Rubber-fabric - its advantage is that it does not conduct electric current, but it is more susceptible to mechanical damage compared to analogues;
Metal sleeve - when using it, a dielectric insert must be inserted from the gas stove to the main line, but otherwise it has the best performance among analogues. In addition, it is recommended by the latest approved standards. Its only drawback is the price, it bites;
Rubber with metal braiding - it is more capable of withstanding serious impacts, and also, thanks to the rubber core, does not conduct current.

When purchasing a hose, pay attention to the color; its braid contains characteristic yellow colors, used only for marking gas equipment.

When purchasing a metal hose, you should pay attention to its coating; some manufacturers focused on other markets, with other standards, use yellow insulation, which does not perform its main functions. Always request supporting documents when purchasing, and keep them in a safe place.

Selecting a convector

How to choose a gas convector? First of all, attention is drawn to the technical characteristics of the unit. The best option is a device with a closed combustion chamber and a cast iron heat exchanger

The presence of a programmable control unit is considered important. Let's look at other factors that you should pay attention to when choosing a household gas convector.

Device power

Since heating occurs due to air circulation, the units operate effectively in only one room. Therefore, each room will require the installation of a separate unit. Power is determined from the calculation: 100 W are required per 1 m 2 of area.

Heat exchanger material

Since gas heating convectors operate on gas, which burns in a special chamber, the heat exchanger is exposed to strong temperature effects. If it burns out after some time, the device fails. Therefore, the material of this part must be resistant to high temperatures. The leader among heat exchanger materials is cast iron. This metal is resistant to thermal stress; in addition, it cools very slowly and distributes heat evenly. Gas convectors with a cast iron heat exchanger can last up to 50 years. The main disadvantages of such devices are the high price and large mass of the unit. A heater with a steel heat exchanger is cheaper and lighter

But when choosing a unit, you should pay attention to the quality of the steel. Steel heat exchangers can last at least 20 years

Combustion chamber type

Heaters may differ in design based on the type of combustion chambers:

Open
combustion chamber. Installation of a unit with such a chamber requires the installation of a chimney with access to the roof. In addition, when the unit is operating, air will be taken from the room to maintain the combustion process. Therefore, good ventilation of the room is required.
Closed
combustion chamber. Such models are more popular because they do not require a pipe outlet through the roof (a coaxial pipe is installed opposite the device). And another advantage is that the oxygen in the room is not burned, since the air is taken from outside the building.

Availability of a fan

A gas convector with a fan quickly and evenly heats the entire room. Due to the forced air supply to the heat exchanger, the latter is cooled better. And since overheating is prevented, the service life of the heat exchanger is significantly increased.

Room type

If you want to install a convector in an apartment

, then the best choice would be a device with a closed combustion chamber and a chimney with a coaxial pipe.
This type of device does not burn oxygen in the room. In private buildings
you can install any. But when using a device with an open combustion chamber, the room must have fresh ventilation.

Type of fuel

The use of liquefied gas is prohibited in apartment buildings. Therefore, the device is connected only to the main line

.
In private homes, a gas convector using bottled gas
can be used, provided that the bottle is installed outdoors in a special metal cabinet.

Amount of fuel consumed

Fuel consumption in gas heating equipment is considered economical. To calculate gas consumption, the following basic parameters are accepted:

1 kW of power will require 0.11 m 3 of gas from the main;
1 kW of power will require 0.09 m 3 of liquefied gas.

Based on these indicators, you can make a calculation. For example, a 4 kW heater (designed for 40 m 2 of area) will consume 0.44 m 3 of gas per hour of operation, and 10.56 m 3 per day. But, since the device does not work constantly, this figure will be significantly less.

Pros and cons of individual gas heating

Please note that the quality of the device, as well as the duration of its successful operation, directly depend on the price of the gas convector. Is it possible to buy a cheap unit and connect it in the house? Yes, but keep in mind that an inexpensive model will last you no more than a year. At the same time, it is unlikely that such a convector will be repaired if it fails.

Let's consider the advantages of gas heating appliances, based on the fact that you did not save money when purchasing and purchased a high-quality unit.

Advantages of gas convectors:

the room heats up quickly,
economical use of fuel,
The device can be easily installed indoors by yourself,
reasonable price,
a gas convector does not require installation of a heating system,
does not destroy oxygen in the room,
the heater can be mounted to a gas cylinder,
the device operates in autonomous mode,
If the convector operates on the principle of natural circulation, then it does not depend on the power supply.

Important: gas convectors with a closed combustion chamber can be installed safely in any room, including the bedroom.

Disadvantages of gas convectors:

in order to correctly install a gas convector connected to a centralized system, it is necessary to obtain permission from the relevant municipal authorities,
the connection diagram for a gas convector requires punching a through hole in the external wall of the building, in the place where the device is planned to be installed,
impressive size,
if you plan to use several gas convectors for heating an apartment or house, then each of them will have to be individually supplied with gas from outside the building.

Important: experts insist on choosing models with a built-in fan. They are more efficient than similar devices with natural convection.

The process of installing a gas convector in a wooden house

There is nothing easier than fixing the converter to a wooden wall; for this you will need:

Self-tapping screws;
Crosshead screwdriver;
Fastenings (included with the converter);
Building level;
Pencil.

First, you should check at what distance from each other are the loops by which the gas convector is hung. Most often, they are wide enough, which allows you to move it left and right, already on the mounts, to a distance of about 5 cm.

Measure the distance between the centers of the seats; it will be the same for the upper and lower hinges. Transfer these dimensions to the wall, observing the height you need from the floor, most often it ranges from 10 to 20 cm.

Attach self-tapping screws to the designated points, and double-check with the help of a convector whether the distances match by bringing it to the heads of the screws. If this is the case, then you can safely fix the hooks to the wooden wall.

When the fasteners are screwed, put a level on them and check the inclination relative to the horizon; it can be leveled by loosening one of the fastenings and lifting it slightly. Now you can hang the gas convector on a wooden wall.

The situation with a wooden house

Installation of a gas convector in a wooden house and installation features are related to the fulfillment of the following criteria:

Identify a suitable site for tube insertion. This is influenced by the type of convector placed: on the wall or on the floor.
Creating a hole through a wall. It does not differ in diameter from the outlet pipe.
At the third stage of installing a gas convector, dowels are attached to a wooden wall to secure the convector itself. Holes are created in the wall for these tasks. When installed on the floor, they are made in the floor.
The device must be connected to the outlet pipe. The connection area is sealed with silicone.
After installing the device, polyurethane foam is used to fill all existing voids.

Mounted gas boiler

Diagram of a mounted gas boiler.

Heating via a mounted gas boiler is convenient due to its lightness and small size. It must be mounted on a load-bearing wall. The mounting rail is placed at a height of 1 meter square meter to 1.6 m. For the exhaust of a coaxial type chimney, it is better to use a detailed diagram. The pipe diameter must clearly correspond to the boiler opening. Self-connection of the boiler to the gas pipe is carried out using a rubber hose, but it is much better to ask gas wiring organizations for help.

Then you should make sure that the connection is tight by applying a soap-based solution to the threads of the connection joints.

Heating from a gas-fired boiler is considered one of the most economical and environmentally friendly types of heating systems for wooden houses. The range of the heated area of one boiler can reach about 350 m2

When selecting the power of a gas-fired boiler, it is necessary to take into account that for every 10 m2 1 meter square meter sq. kW is enough. There are double-circuit and single-circuit boilers

General heating is installed using single-circuit systems, while double-circuit systems. In addition to this, the issue of hot water must be resolved, heating from 60 to 200 liters of hot water. There are also 2 types of ignition: automatic and manual, activated with a button. There are natural and forced draft of boilers. If the removal of exhaust gases is carried out due to the draft created in the smoke exhauster, then this is a natural draft gas water heater. When gases are removed using a built-in fan, it is a forced draft boiler.

When installing a gas-fired boiler in a wooden house, any installation process and installation must strictly comply with repair and technical regulations and strictly follow safety needs. Control devices for gas-fired boilers have automatic functions. The housing contains burners, a heat exchanger, a device for determining pressure, a security system, circulation pumps, a thermometer, and an expansion tank. Installing a gas-fired boiler without outside help, without the services of heating system companies, is quite possible. Everything related to the installation of the device itself, the installation of pipes for the water supply system and the connection of electrical power can be done with your own hands.

However, it is better to contact special organizations regarding gas distribution. A gas heating boiler is the most popular method of general heating system today. Inexpensive organization, installation and work make it possible to choose in favor of purchasing and installing gas-fired boilers for wooden houses.

Gas water heaters for heating systems

More details on the website ust-stroy.ru

Characteristics of gas convectors

Looking at heating reviews, we can say that consumers highly rate these devices. And this is not surprising. After all, gas-type convectors have a lot of positive aspects. Of course, like any device, there are a number of disadvantages, but they are not significant.

The main advantages are:

The disadvantages include the need to obtain permission for installation, the gas pipeline must be connected separately to each convector, the dimensions are slightly larger than those of a water radiator. The most important disadvantage is that quite large holes will have to be punched in the outer wall for installation.

Manufacturers

In recent years, gas converters Danko, Ross and some others made in Ukraine have become very popular. At a low cost, they are quite reliable. Externally, they are far from ideal, but they look neat. If we talk about models that look great, these are Turkish Demrads. There are only good reviews about them in terms of performance characteristics. At the same time, the similar-priced Eskabe is not encouraging, since its exhaust has a very high temperature, which indicates low efficiency.

Approximate prices for one convector using bottled gas in online stores

In general, a fairly large number of companies have normal reviews from owners:

Danko (Ukraine)
Ross (Ukraine)
FEG (Hungary. There are models with a glass door for viewing the flame)
Demrad (Türkiye)
Mora (Slovenia)
Baxi (Italy)
[email protected] Emax (Hungary)
Karma (Czech Republic).

There are many other companies on the market, especially many European ones. In Europe, radiator heating is not so widespread, so they heat themselves with “air heaters” using bottled gas. Branded convectors have a high level of equipment safety, but so do their prices...

Construction of a gas heating convector

Any convector running on gas consists of the following components:

A gas burner in which a mixture of air and gas is burned;
Cast iron or steel heat exchanger. It is located behind the grille in front of the gas radiator. The heat-resistant coating of the heat exchanger allows it to withstand high temperatures. A cast iron heat exchanger is more durable, its service life is more than 50 years, at the same time it is more expensive and heavier than its steel counterpart;
Gas valve. Acts as an automatic device: turning on/off the burner; adjusting the volume of air-gas mixture supplied to the burner; temperature control in a heated room; gas supply pressure adjustment.

Important! It is not recommended to make changes to the gas valve settings yourself, because this may lead to damage to the convector or fire hazards

It is recommended that the factory settings be retained, or changes should only be made by qualified personnel familiar with similar gas equipment.

Frame. Warm air enters the room through a heat-resistant grille, which is painted with heat-resistant paint. It is not allowed to use a gas heating convector without a grille;
“Chimney”, which is a steel coaxial pipe (pipe-in-pipe system, which saves space and installation time). Through a galvanized steel pipe of larger diameter (15 cm in diameter and 60 cm in length), air is drawn in to operate the burner (a cap is also installed on this pipe to protect the structure from the wind), through another “internal” aluminum pipe (10 cm in diameter and 64 cm in length ) combustion products are released. Air for gas combustion comes only from outside (the air in the room is not used in the combustion process), because the air intake pipe is connected to a special closed chamber, which is separated from the room.

Device design and operating principle

Let's start with the definition of a gas convector. This heating device is not an analogue of a gas boiler. It works on a completely different principle - it heats not the coolant, but the air. Gas convectors are installed in relatively small rooms, as they heat the air locally.

The design of this heating device is relatively simple. The gas convector consists of the following parts:

heat exchanger in which the air is heated,
programmer - a device responsible for maintaining a certain temperature in the room,
control panel , on which indicators are displayed,
gas valve that controls the gas supply,
fan No. 1 , responsible for supplying air to the heat exchanger and valve,
fan No. 2 , which disperses heated air throughout the room.

How does a gas convector work? Everything is quite simple: it operates on the principle of a gas burner. Cold air from the outside, obeying the laws of physics, enters from below, heats up and exits through the hole at the top of the device. Note that gas models can function due to natural or forced convection. In the second case, air is pumped by fan No. 1.

How to choose a gas convector

When choosing equipment you will need to consider the following:

Power calculation. When heating a room, air convection is used. Consequently, heaters are only effective in limited spaces. For each room you will need to install a separate convector. Power calculation is carried out according to the formula 100 W per 1 m².
Type of housing. Heaters with a closed combustion chamber and exhaust of combustion products through a coaxial chimney are suitable for apartments. You can install any type of equipment in your home. But when installing a heater with a closed chamber, it is necessary to take care of a constant and intense flow of fresh air.
Fuel type. A gas heating convector running on liquefied gas is prohibited from being installed in an apartment in a multi-storey building, due to the high explosion hazard of the cylinders.

All convectors are initially manufactured with the ability to connect to the main gas pipeline. If you plan to connect the gas convector to the cylinder in the future, you need to purchase a special reducer (in some modifications it is included in the kit).

Advantages of backup heating of the house with liquefied gas from cylinders

In the article: “House heating with gas cylinders. Personal experience”, we explained in detail whether it is profitable or not to heat a cottage with liquefied gas. To summarize the material, this option is worth considering:

If the house has a small area (about 50-70 sq. m).
The house is well insulated.
The property owner has no other alternative, and the allocated power of the electrical grid is not enough to afford cheap heating with electricity at the night tariff.

To this we add the constant loss of time and money (for gasoline), because... The owner of a liquefied gas heating system will most likely have to take cylinders to refuel weekly.

Therefore, we will consider heating with gas cylinders only as a temporary, backup and energy-independent heating system, so as not to freeze in winter and somehow survive for 2-3 days in case of failure of the main heating system or a power outage.

DekagonFORUMHOUSE user

I built a frame house with an area of 90 square meters. m in the form of a coaxial yurt. The house is currently being used in the “dacha” mode, i.e. I only come there on weekends. There is no main gas. Electricity is one phase. The voltage fluctuates from 150 to 230 Volts. There are no long outages, but once a truck knocked down a power pole. No one is immune from emergency situations. I was wondering how I could heat the house, and this is what I came up with.

The user analyzed all types of heating available to him:

solid fuel stoves-fireplaces;
gas tanks;
electric boilers;
IR heaters;
heat pumps;
alternative energy.

As a result, electric and gas convectors turned out to be the easiest to install, cheapest in cost, easy to use and easy to automate. Moving a little away from the main topic of the article, let’s say that electric convectors are controlled through timers and thermostats. This allows Dekagon to arrive for the weekend (by Friday evening) to raise the temperature in the house from the “standby” level to a comfortable level in advance. Those. from + 15 °C to + 23 °C and do not waste time warming up the premises.

Now the arguments for using a body generator powered by liquefied gas are interesting.

DekagonFORUMHOUSE user

When my house was being built in winter, the builders lived in a change house. There was no electricity either. I was thinking about how to warm the workers. I wanted to buy them a “potbelly stove”, but a good solid fuel stove is expensive. We still need to install a chimney. Harvest, store, saw, chop firewood. Extra hassle. I took a gas convector with a power of 2.2 kW. In 2014, it cost me 8,500 rubles. The device is immediately ready for use, just connect it to the cylinder. During operation, the gas convector showed its best side. Works efficiently and safely, autonomously. The thermostat keeps the set temperature. In general, I liked it so much that I decided to move it into the house in case of a power outage.

For gas, the user bought a modern composite (rather than heavy steel) 24 liter cylinder. I also additionally purchased a kitchen tile with two electric and two gas burners.

The stove is connected to a gas cylinder, from which the gas convector operates.

A year later, Dekagon bought a stationary gas fireplace with a capacity of 7 kW.

A gas convector and fireplace work when it is necessary to reduce the load on the electrical network, and as a reserve in case of a power failure.

The fireplace operates from a second gas cylinder, is automatic, and combustion products are discharged through a coaxial chimney.

Street air enters the combustion chamber through the outer pipe, and combustion products are removed through the inner pipe.

Installation of a gas fireplace or convector is not difficult and is accessible to everyone. The user made a hole in the wall, hung the heat generators on the wall and connected them to gas cylinders.

In the event of a power outage, gas convectors will allow you to comfortably survive for several days until the breakdown is repaired.

Bottom line: Dekagon heats the house with electricity and from time to time gas heat generators. Let's look at the costs for a combined heating system. So, the heating season lasts 7 months. In addition to electric and gas convectors, the house is equipped with infrared electric heaters and several IKZK lamps. Water for domestic hot water is heated from electricity. Household appliances, lighting, etc. work.

Electricity consumption for the heating season 2014-2015 is 8000 kWh.
Electricity consumption for the heating season 2015-2016 is 6800 kWh.

In the 14-15 season, the electricity tariff is 3.15 rubles. for 1 kWh. Total (8000 x 3.15 = 25,200 rubles) / 7 months. = 3,600 rub. 1 month for electricity.

In the 15-16 season, the electricity tariff is 3.45 rubles. for 1 kWh. Total (6800 x 3.45 = 23,460 rub.) / 7 months. = 3,350 rub. 1 month for electricity.

Let us remind you that the area of the house is 90 sq. m. m. The cottage is used on weekends. Those. From Monday to Friday the premises are maintained at +15 °C. On Friday and Sunday + 23 °C. Climatic zone of the middle Volga.

Liquefied propane-butane gas (LPG) is used as backup heating and for cooking . During the season, 3 cylinders (20 liters of gas) are used. This is about 1200 rubles.

Gas heater. Flaws in work

Next, you should deal with the disadvantages of convectors. The main disadvantage of such a device is that you have to break through the wall to complete the installation. Moreover, a hole is needed here for the coaxial gas outlet, which is a special tube in the pipe through which exhaust gases exit. The fresh air required for combustion is supplied to the convector thanks to an external pipe. It can be assumed that the hole in the wall may be located in a certain area where the convector itself will be placed. If they are located under every window of every room, then there will be a lot of holes in the walls, and they cannot be hidden or placed in one area. In addition, additional space must be made in the wall for the gas supply.

If a standard heating system is used in a living room with an area of 30 square meters with two windows, almost under each window it would be worth installing one convector. However, with gas convectors this option is unacceptable. Here you should install one convector with increased power in a certain area on the outer wall of the room (where there are the most optimal conditions for supplying gas and creating a discharge for exhaust gases). This installation does not imply creating a temperature balance in the room. One corner will be quite hot, and the other will be cold. To create proper comfort, one low-power convector should be placed under each window. However, here the question of price arises, which will double, although the aesthetics of the room will increase. Hence the conclusion - the installation of this heating option will be in many ways inferior to a standard water heating system.

The gas convector includes low inertia. In other words, it heats up quite quickly and cools down at a similar interval. This feature can be attributed to both pros and cons. It all depends on how the device is used. Using it in a residential area can negatively affect the comfort of the temperature regime, but installing it in a garage, barn or workshop will undoubtedly give positive results.

Another nuance in the operation of a gas convector, which can also be considered a plus and a minus, is the presence of a combustion chamber, where the gas heats the chamber, which subsequently heats the air. For the durability of the convector, its design must contain steel that is resistant to fading. It’s good if the device is equipped with just this type of specialized steel (however, the price of the device will double). If the convector uses cheap steel, then it runs the risk of failing very quickly due to corrosion, burnout and other factors. If the combustion chamber in the convector is created using 10 mm cast iron, then the service of the device will be durable.

Flaws

The device heats only one single room, the one in which it is installed. When the doors are open, the neighboring rooms will warm up slightly.
Only air is heated; hot water supply (DHW) is not provided.
Despite the beautiful appearance of modern gas radiators, which can fit into almost any interior, they cannot be “hidden” behind other interior items, because For safety reasons, it is prohibited to install any flammable materials near them.

Video

There is 1 comment on the entry “Gas heating convectors: design, installation, advantages”

Hello, I’m interested in gas heating from Bolons, I need to heat 200 sq m, how much will it cost and do you work in installments for a year in advance?

Leave your comment

From the author:

We welcome you, dear friends!
We suggest we talk about how to install a gas convector with your own hands .
These heating devices are less popular among consumers than their electric counterparts. The fact is that this type of heater implies the presence of a centralized gas supply or a gas cylinder. But such models are much cheaper to operate. They are usually installed in dachas or country cottages - that is, in those locations that do not require constant heating.

Tips for use

If we talk about tips for operating this category of equipment, the first thing I would like to mention is that you should definitely read the operating instructions before use. Many people neglect this simple advice, although from the instructions you can learn a lot of operating features of a specific gas converter model. Also, do not neglect the services of an installation specialist . He will be able to correctly install the device. This will allow you to simply save time and money, so that you don’t have to redo it later if you did something incorrectly.

In addition, before installation it is better to make the necessary calculations so that the installation accuracy is maximum.

For a review of the operation of the gas convector, see the following video.

How does a gas convector work?

Operating principle of convectors

Inside the convector there is a heat exchanger connected to convection channels.
The heat exchanger heats up when gas is burned.
The air passes through the heating element and heats up.
Heated air flows enter the room.

Advantages of gas convectors

Lower gas consumption - the air in the room is heated directly, and not thanks to the coolant, which increases the efficiency of the equipment and reduces heating costs.
No need for coolant. Heating of the room is carried out using air heating. Convectors can be installed in unheated rooms, starting only when necessary, without fear of freezing of the heating system. For this reason, installing a gas convector for a summer residence is the best option.
Versatility - the heater is connected to a central gas pipeline or cylinders. For the convector to operate, a connection to a combustion products exhaust pipe is required. Connection to the power supply network is necessary only for convector models with a fan. The fan accelerates air circulation and increases the rate of heating of the room several times.

To install a gas heating convector in an apartment, you need to obtain permission from the gas service and prepare a heating project, the same as for a hot water boiler.

When and why is it effective to use gas convectors?

Gas convectors have low resource consumption, but are not able to develop the required power to heat large rooms. Therefore, the scope of their application has become small private houses with one or two living rooms, cottages, garages and temporary buildings. In such conditions, the heating gas convector provides the following advantages:

compactness, relative cheapness and ease of installation of equipment;
no need to develop and approve project documentation;
autonomy when the convector is powered from gas cylinders;
high efficiency (up to 90% in industrial devices and up to 80% in home-made convectors);
resistance to low temperatures, no “freezing effect”;
using atmospheric oxygen rather than indoor oxygen;
fuel versatility, that is, the ability to switch from methane to propane by replacing nozzles.

Among the disadvantages of the system, the most significant are serious losses in efficiency when heating large rooms and an increase in their warm-up time.

The second problem is partly eliminated by installing convectors with forced circulation, that is, equipped with a blower fan, however, in houses with three or more rooms, the rationality of such a solution is very doubtful.

Another problem that may arise when trying to convert an apartment for convector heating is a ban from the municipal gas service, caused by the potential danger of the device for neighbors. Therefore, residents of apartment buildings need to coordinate such work in advance.

Gas supply main stages

The installation of the gas convector has been completed, now we need to get started with the gas supply. This stage is quite complex and responsible at the same time. To supply gas, do the following:

According to regulatory documents, the pipe leading to the convector must go along the street. There are two options here: the first is that the pipe has a pre-installed threaded connection, the second is that there is no such connection. If there is a thread, then you can screw on the gas valve yourself, which will shut off the gas supply to the convector. If there is no withdrawal, one must be made. To do this, call professional gas welders from your local Gorgaz or similar office.
After installing the gas tap, it is necessary to run a metal-plastic pipe to the convector itself. Using a tape measure, calculate the length of the pipe, simultaneously determining the presence of fittings.
You need to buy pipe and fittings. The principle of purchase is that the seller must clarify the availability of a certificate of conformity of these pipes and fittings for this type of work.
Lay the pipe, secure it with clips every m. To install the clips, you need to drill holes in the wall.
When installing the necessary fittings, carefully lubricate the pipe and the fitting itself with silicone, which will provide additional sealing. Silicone will also serve as a lubricant and will make pipe installation easier.

As a result of the work, you should receive a convector mounted on the wall with a gas pipe connected to it.

Now the last stage of installation remains. A test run is required.

Before starting, open the gas tap and go over all fitting joints and threaded connections with a brush moistened with a water solution of soap or shampoo. This way you will be able to notice inflated bubbles (if any), which indicate gas leaks. If this happens, immediately turn off the gas supply valve. After checking the joints, start the convector. To do this, hold down the gas button for one minute. This way the gas will have time to pass through the pipes and enter the combustion chamber. Press the piezo igniter, a spark should ignite the gas. A blue flame will flare up in the firebox.

Adjust the operation of the convector by setting a comfortable temperature. During the first few hours of operation, you may smell an unpleasant odor of burning oil. This is normal, since the convector is new and the combustion chamber burns out. If the smell lingers for a long time, then you should turn off the gas and check all joints and threaded connections again.

It is advisable that all work on the installation of gas convectors be carried out by a professional who has sufficient experience in performing such work. This is also due to the fact that installing a convector yourself may void your warranty on the device. The gas convector must be accepted into the balance sheet by Gorgaz.

You must have a documented permit for the tie-in. In addition, all installation decisions, as well as the conclusions of the commission for acceptance of the device into operation, must be documented and signed in the appropriate manner.

The current market for heating devices is quite wide. Among such devices, it is worth highlighting the gas convector. The range of heating systems includes a lot of gas convectors of various shapes.

Necessary materials

To install this device, you should have a set of necessary tools and materials on hand:

the gas convector itself;
metal-plastic pipe with metal fittings;
pipe cutter;
a wrench that is suitable for tightening the fittings used;
silicone for plumbing work;
gas tap;
a powerful hammer drill with a special blade-shaped crown;
drill;
Phillips screwdriver;
polyurethane foam that can withstand high temperatures;
high temperature silicone;
plastic dowels and screws for them.

Return to contents

Gas connection

Friends, at this stage it is important to be extremely careful! Let's say that you do not have the skills to work with gas appliances - then to perform the following work it is better to contact specialists

Installation of a gas heater to a gas supply source proceeds according to the following algorithm.

Let's imagine that there is a special threaded outlet on the gas pipe. Then you just need to screw a gas valve onto this pipe. If there is no special allotment, then one will need to be made!
The next step is to bring the gas pipe to the convector and connect them using a fitting. This process cannot be rushed.
Secure the supplied pipe with special clips. The distance between them is 1 meter. To do this, you will need to drill holes on the outside wall of the building.
Treat fittings and pipe joints with silicone to ensure a tight seal.
Be sure to call your gas service representative to ensure proper installation and connections.

Required tools and installation diagram

The next step after purchasing the device is preparation for installation. Make sure you have the following materials and tools on hand:

pipe cutter,
drill,
drill,
adjustable wrench,
spanners,
screwdrivers,
hammer drill,
spatula,
silicone (plumbing, high temperature),
screws and dowels,
gas tap.

Now you can move on to the next stage - choosing the installation location.

It is important to act in accordance with GOST! Before you begin installation, take careful measurements, markings and “trying on” the convector. Please note that the room in which you plan to install the heater must be prepared. Remove furniture from the room or cover furnishings with polyethylene, since working with a hammer drill is a rather dusty business.

Installation of a gas convector is carried out according to the following scheme.

Decide where the hole for the gas pipe entry will be.
Make a hole in the wall with a hammer drill, focusing on the diameter of the future pipe. This stage is the most labor-intensive.
The next step is to drill holes for the heater mounts and hammer in the dowels.
Connect the convector to the exhaust pipe. Be sure to seal the joint with silicone that can withstand high temperatures.
The heater is attached to the wall with self-tapping screws. At this stage you will need help, because the unit has an impressive weight.
The final stage of installation is to fill holes and cracks with foam to prevent cold air from entering the room.

We bring to your attention an educational video dedicated to the installation of a gas convector.

Gas boiler for floor

A gas boiler for the floor is mounted either on a concrete base or on an aluminum sheet protruding at least 300 mm beyond the perimeter of the device. If this is a closed chamber combustion system, then a coaxial type chimney is used, the opening of which can be located either on the back wall of the device or on the top panel. The chimney must be placed away from the window to prevent gases from penetrating back into the room. The smoke exhaust pipe must have a slope to remove condensate due to the temperature difference. When installing vertical heating equipment, the hole for the smoke exhauster in the top panel must be at least 15 centimeters higher than the equipment itself. After the installation of the chimney is completed, you can turn on the water supply devices.

If you need to determine a gas water heater for individual buildings, then the device must be placed in a specialized pocket, which has a recess of about 30 centimeters with a concrete screed and walls lined with fireproof materials.

Convector installation

Before installing a gas convector, you must study the installation requirements and recommendations, which are described in the instructions for the device.

Before installing the gas convector, you need to choose a place to place it. According to GOST, the unit must be mounted under a window.

The main installation steps are described below.

We try on the device to the chosen location, using a tape measure we transfer the places for the holes for the chimney and gas pipe. In some models, the gas pipe is supplied from below, so it is necessary to leave space for its connection.
After this, the most labor-intensive operation has to be performed - punching a large-diameter hole in the wall for the exhaust pipe. You can use a hammer drill and make a hole with a diamond bit. If you don’t have a crown, you can break through the wall by switching the hammer drill to jackhammer mode (when using the hammer drill, a lot of dust will be generated, so cover all the furniture with foil in advance).
Next, you need to prepare holes for fasteners and hammer dowels into them.
Now you can connect the pipe to the heater and treat the connection with sealant (high temperature).
Lift the device together with the pipe and insert it into the hole in the wall, then secure the device with self-tapping screws. Since the unit is quite heavy, you will need help to lift it. The floor heating unit has special legs.
After this, it is necessary to seal all the cracks between the chimney and the wall with high-temperature sealant or foam.
At the end of the chimney, attach a cap that prevents the flame from being blown out by the wind (the cap and fasteners for it are included with the device) - the installation of the gas convector is completed.

In conclusion, we can say that the use of gas convection equipment can be a relatively simple and inexpensive solution to the heating problem for different types of premises. It is attractive that the installation of such equipment does not cause much difficulty (except for connecting the device to the main line).

During the cold season, various devices are used to heat the room. One of the most popular today is the gas convector. As a rule, after purchasing this device the question arises: how to install a gas convector?

If the installation is carried out in compliance with all requirements, the room will be warm and the device will function correctly without endangering you.

Test run

Before testing the device, open the gas valve and go over all important areas with a brush. Wet it with soapy water. The important areas are where the fittings and threaded contacts meet.

If swelling bubbles appear, immediately close the valve and eliminate the leak area.

After this, the unit can be turned on: the gas button is pressed for a minute. Fuel follows all pipes to the combustion compartment.

Next, start the piezo ignition - press the corresponding igniter. The spark ignites the gas and a blue flame appears in the firebox.

At this stage it is necessary to configure the operation of the device. During the initial hours of operation, it may smell like flaming oil. This is a common situation. The unit is new. The combustion department in it burns out.

If this smell persists for a long time, turn off the gas and look at the area where the exhaust pipe and the convector outlet connect.

Premises requirements

Gas service requirements for premises:

Ceilings should be no lower than two and a half meters, which is important, because many wooden houses are built with low ceilings, and this is with the least powerful equipment; The diameter of the ventilation duct must be equal to or exceed 100 mm, the material from which it is made must comply with SNIP, and the lower part of the ventilation duct must be at least 200 mm below the ceiling; Bottom gaps on interior doors must be at least 25 mm; Each room should have windows to ventilate the room; The boiler room must be equipped with a door to the adjacent non-residential premises, and when installing a boiler with a power of over 150 kW, a separate entrance door; The internal space of the boiler room must have at least 7.5 m3 in volume; for new houses this requirement has been doubled; The chimney must be equipped with two walls, its diameter must be greater than or equal to the incoming pipe of the equipment; Lighting in the boiler room must be safe; for this purpose, open light bulbs without shades are not allowed; In the case of external electrical wiring, it must be placed in specialized cable channels; The indoor gas control system should be installed in a wooden house if the boiler is located in the basement.

Features of use

First of all, people are concerned about the issue of safety, because wood is a quickly flammable material, which means that when installing such equipment there are risks of fire, and the positive action coefficient of gas converters leaves much to be desired.

On the other hand, the installation process is much simpler than batteries filled with hot water, to supply which you will have to install a bulky heating system.

There are often cases when the original design of a wooden house did not provide for any heating at all, but during operation the owner changed his mind, and installation of heating devices is required after the fact. Many gas convectors can easily satisfy such needs, because they are able to operate on gas supplied from a cylinder, and not from the main line.

In order to obtain permission to install a gas convector in a wooden house, you need to make a visit to the gas or fire department, depending on the source of gas, but first things first.

How to install a convector correctly

Installation of a gas convector in a wooden house. During operation, the housing heats up to 50-55°C. It is necessary to insulate wooden surfaces in contact with heating parts of the structure. Installation rules in a wooden house require the manufacture of fireproof roof breaks. If a coaxial pipe is used, insulation is not required at the point where it passes through the wooden wall. The surface of the coaxial chimney heats up slightly due to the special design of the burner and pipe.
Location from the floor. Air heating of a country house or residential building has certain features that affect the heating efficiency. To ensure maximum performance, the convector should be installed as close to the floor as possible. As a result of this solution, the intensity of circulation of convection flows increases and the efficiency of the equipment increases.
The gas pipe is supplied to the heater exclusively through the street. A shut-off valve should be installed at the connection point.

A test run is carried out in the presence of a gas service representative. A corresponding note is made in the convector documentation.

Which is better, a gas convector or a boiler?

Air heating is recommended for use in country houses that are not heated in the winter. During installation there is no need to use a water circuit; the building can be heated only from time to time. Even at negative temperatures in the room, you can warm up the room in 20-30 minutes.

A gas convector for a home using bottled gas is inferior to a boiler connected to the main pipeline in terms of efficiency, but superior in functionality. The choice of an air heater is justified in the absence of gasification. With a fully charged cylinder, the heater will operate for approximately 10 days.

A convector heats a room better and faster and uses less fuel, but its effectiveness is limited by the properties of convection currents. The heating intensity decreases as obstacles arise: walls, furniture, etc.

For heating a country house or small rooms, a convector type heater is optimal. But for residential heated houses with large rooms, it is better to install a traditional gas boiler.

The current market for heating devices is quite wide. Among such devices, it is worth highlighting the gas convector. The range of heating systems includes a lot of gas convectors of various shapes.

Equipment startup and performance check

Before you start using your new heating device, it is important to conduct a test run. You should proceed according to this scheme.

Open the gas valve and check the system joints for leaks.
After checking, you can turn on the convector. For the first time, you need to hold the start button for 1 minute and wait until the gas penetrates the combustion chamber.
Do you see the burner lit? Now you can adjust the operation of the convector.

Important: installation of a gas convector in a wooden house is absolutely safe, because fire hazardous parts are located in the inside of the heater.

To summarize, we note: despite the fact that a gas heater is not a very popular heating device, it can be used to create a comfortable temperature in dachas and country houses. The unit quickly and efficiently heats the air in the room, and at the same time is much more economical than an electric radiator. Another obvious advantage is the ability to connect to a gas cylinder. One dubious circumstance can be considered that the gas convector heats only one room, and not the whole house, unlike a gas boiler connected to the heating system.

We hope that the article was useful and helped resolve the problem!

Wall-mounted gas boiler

Diagram of a wall-mounted gas boiler.

Heating using a wall-mounted gas boiler is convenient due to its lightness and compactness. It should be installed on a load-bearing wall. The mounting strip is located at a height of 1 to 1.6 m. To drain a coaxial chimney, it is better to use a detailed diagram. The diameter of the pipe must clearly correspond to the boiler opening. Self-connection of the boiler to the gas pipe is carried out using a rubber hose, but it is best to seek help from gas wiring organizations.

After this, you should make sure that the connection is tight by applying a soap solution to the threads of the connection joints.

Gas boiler heating is one of the most economical and environmentally friendly types of heating systems for wooden houses. The range of heated area of one boiler reaches about 350 m². When choosing, keep in mind that for every 10 m² 1 kW is sufficient. Exist . General heating is installed using single-circuit boilers, while double-circuit boilers in addition to this solve the issue of hot water, heating from 60 to 200 liters of hot water. There are also 2 types of ignition: automatic and manual, activated using a button. A distinction is made between natural and forced draft boilers. If the removal of exhaust gases occurs due to the draft created in the chimney, then this is a natural draft gas boiler. When gases are removed using a built-in fan, it is a forced draft boiler.

When installing a gas boiler in a wooden house, any installation and installation must strictly comply with construction and technical regulations and strictly follow safety requirements. Gas boiler control devices have automated functions. The housing contains burners, a heat exchanger, a pressure gauge, a safety system, circulation pumps, a thermometer, and an expansion tank. Installing a gas boiler yourself, without the services of heating systems companies, is quite possible. Everything related to the installation of the device itself, the installation of water supply system pipes and connecting the power supply can be done with your own hands.

However, it is better to contact specialized organizations regarding gas supply issues. A gas heating boiler is the most common method of general heating system today. Cheap organization, assembly and operation allow you to make a choice in favor of purchasing and installing gas boilers for wooden houses.